UGC Approved Journal

Abstract:

In this project we aim in placing a heat detection system in a car . The heat detection system would sense the rise in temperature inside the car. Because of increase in temperature during day time the requirement of cooling system in absence of person inside the car is a major concern. In order to meet this requirement a method to reduce the temperature inside a car is required .In our project we are using DHT-11 sensor to detect the heat change inside the car .This sensor which is connected by an Arduino uno board sends the signal to the motor which slides down the window and cools the interior . After attaining normal temperature the window again slides up. In the past few years many fatalities have been reported as the result of internal car heat. Problems arise when the temperature in a car cabin is too hot when parked under direct sunlight. The trapped and accumulated heat causes the temperature inside a car to reach temperatures soaring high temperatures..
Keyword: Arduino , Car cabin, Heat Detection

Copy and Paste

Mr.K.K.Naveen kumar, Mr.S.Srinivasan, Mr.A Ashfaq Ahmed, Mr.Sachin Shankar "Design and Fabrication of Heat Detection System in a Car Passenger Cabin " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

At the Institute for Thermodynamics at the Bundeswehr University Munich a piston-driven shock tunnel is operated to investigate structures of space transportation systems under reentry conditions. For temperature measurements in the nozzle reservoir under single-shot conditions, laser-induced grating spectroscopy (LIGS) was identified as best-suited measurement technique. However, under moderate conditions seeding of the test gas with NO2 was used successfully to improve the signal-to-noise ratio of thermal signals. For a better understanding and an optimization of the seeding process, an optical setup for an absorption measurement in a test cell in the used spectral range of the LIGS measurements (592 nm - 596 nm) was developed. The measurements of NO/N2-seeded dry air showed......
Keyword: absorption, shock tunnel, laser-optical measurements, reaction kinetics

Copy and Paste

T. Sander, P. Altenhöfer, L. Kleiner, Ch. Mundt "Investigation of NO2 Absorption Behaviour around 593 nm for Seeding Purposes " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

Pelaparado Watershed is one of the watersheds in the Sumbawa River Basin. Pelaparado watershed is one of the watersheds that has fluctuating water availability between the dry season and the rainy season, so a reservoir needs to be built in terms of managing the water. Overall the area of irrigation in the Pelaparado River Basin is 2,893 ha and supplies to the Keli watershed with an irrigation area of 995 ha. The benefits of pelaparado dam are as irrigation, the supply of raw water and as electricity. The Pelaparado Dam has the following technical data: 1) Total catchment area of 85 km2, 2) Area of inundation 104 ha, 3) Maximum storage of 18 million m3, 4) Effective storage of 15 million m3, and 5) Intake capacity of 3.5 m3/s. The results of this study.....
Keyword: Dam, Pelaparado, Sumbawa..

Copy and Paste

Aripin, Suryawan Murtiadi, Buan Anshari "Study Operational Of Pelaparado Dam in Pelaparado Cacthment Area of Sumbawa River Basin (Ws) " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

This paper purpose is monitoring of noise level at various sites of industrial & commercial area of Faridabad. Statistically analysis of both monitored results & noise calculated by prediction noise models & through regression analysis check validation of calculated noise by some defined prediction models & designed prediction noise models. By sound level meter, observed Leq is monitored from 15 samples in a hour & how many vehicle's like as Bus, Truck, Bike, Auto, Car, Jeep passing at a every selected location is monitored in morning & afternoon times in continuous 4 days(selected location 60 samples each is taken). As well as road width is measured, % of heavy vehicles, % of light vehicles & other's vehicle's no's feed into prediction noise models & calculated Leq....
Keyword: Industrial area, Commercial area, Equivalent noise, Noise monitoring

Copy and Paste

Tarachand,Syed Khursheed Ahmad, Ghanshyam "Study Operational Of Pelaparado Dam in Pelaparado Cacthment Area of Sumbawa River Basin (Ws) " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

The assessment attributes reviewed by the priority scale on the increase are the level of road damage, Average Daily Traffic, road class, land use, and road network, while for the construction is the road network, specifications for the provision of road infrastructure and road classes. The weighting results of the AHP technical factors were (83.33%) and non-technical (16.67%), the non-technical factors had attribute assessments of the Development Planning Deliberation (10, 44%), community proposals (4.66%) and specific policies (1.56%). For weighting technical factors for improvement (69.44%), reviewed based on the largest attribute assessment is the level of road damage (38.21%), road.....
Keyword: priority scale, provincial road, improvement, development, AHP.

Copy and Paste

Nunuk Retnowulansari, Iphan F. Radam "The Priority Scale of Handling the Province Road in South Kalimantan " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

The study has conducted to determine the workability and compressive strength of the self –compacting concrete. Concrete that flows and settles due to its own weight without segregation and bleeding is called selfcompacting concrete. SCC is a type of concrete that can be placed in the form work and it passes through any obstruction by its own weight and does not require any vibration Modern application of SCC is focused on high performance, better and more reliable and uniform quantity. Japan, started in late 1980's to develop SCC. By the year 2000, the SCC has become popular in Japan for prefabrication products and ready mixed concrete. Fly ash contains the basic ingredients.....
Keyword: SCC, Quarry dust, Fly ash, NDT tests, Flow Properties.

Copy and Paste

Kakarla Gopinadh, Dr. Kota Srinivasu, Jujjuri Ushakranthi "A Study on Influene of Quarry Dust on Behaviour of Self Compacting Concrete " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

The construction industry is one of the largest sector in the world and plays a vital role in budget and ultimately economic growth of the country. Performance of construction of infrastructure projects has most complex behavior hence prone to the failure of project. These failures directly affect the economy of the nation as well as Institutions. Numerous risks being faced during lifecycle of the infrastructure projects, due to their inherent complex nature, intricate relationship between the stakeholders, casual approach towards the identification and control of the uncertainties leads to the failure of the projects. Thus, consistent failures of the infrastructure projects attracts attention towards study on scientific approach to identify, analyze, plan & control of the risks frequently encountered....
Keyword: Infrastructure, Risk Management, Scientific Approach, Quantitative Analysis

Copy and Paste

Ashwini R. Patil, Keshavrao B. Lawand "Risk Management in Infrastructure Projects – A Case Study on Pune Metro " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

Introduction: Repetitive strain injuries and work-related musculoskeletal disorders are musculoskeletal problems. Nursing is one of the areas most affected by these issues because of the profession's risk factors. Objective: To evaluate the impact of a distance learning course about prevention of repetitive strain injuries/work-related musculoskeletal disorders on quality of life, discomfort and pain, and presenteeism and absenteeism in nursing professionals. Methodology: Sixty nursing workers participated in the clinical trial and were randomized into two groups. The intervention group took an eight-hour distance learning course and the control group saw a thirty-minute educational lecture. Results: Regarding perceived quality of life, better results were not observed in the intervention....
Keyword: Musculoskeletal Diseases, Nursing, Prevention, Quality of Life, Occupational Health

Copy and Paste

Renata Cristina Rocha da Silva, Antônio Cardoso dos Santos, Michele Cristiene Nachtigall Barboza "The impact of distance learning on nursing workers' health – a randomized clinical trial " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

The objective of the paper is to study whether there is significant difference in the perceptions of students of public and private university colleges in selected universities in Andhra Pradesh in India, which is part of quality education. The study is vital since the measures of quality of education varies from one kind of university to the other (viz., public and private universities) and are determinants of student satisfaction. Measuring student satisfaction is more important since it is an indication of how far the universities are successful in providing quality education. Student satisfaction can be understood as student's perception of the services provided by the.....
Keyword: Quality of Education, Higher Education, Student Satisfaction, TQM, Management Education, University System.

Copy and Paste

Prof. T.Sreenivas, Mrs.Ch. Kiranmayi "Student's Satisfaction on Quality Standards of Management Education at Public and Private Universities in Andhra Pradesh – A Comparative Study " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

The aim of this study was to evaluate the oregano and rosemary essential oils as partial substitutes the salt on the quality of chicken sausage. Three formulations of 6 kg each were made: the formulation 1 was made the sausage with no reduction of salt, and the formulations 2 (O1) and 3 (O2) were prepared using sausages with a partial reduction of salt added with essential oils of oregano and rosemary. The products obtained were subjected to physicochemical, microbiological.....
Keyword: Consumers, Natural antimicrobials, Quality, Spices, Meat products.

Copy and Paste

Gilmar Freire da Costa, Chimenes Darlan Leal de Araujo, Fernando Luiz Nunes de Oliveira, Geíza Alves Azeredo "Preservation of chicken sausages using oregano and rosemary essential oil " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com

Abstract:

Healthcare industry collects large amounts of clinical data of patients. Although this data is useful but not provides hidden information for effective decision making. Advanced data mining techniques can be used to discover hidden pattern for effective decision making. Medicinal data mining methods are used to analyze the medical data. Medical data mining content mining and structure methods are used to analyze the medical data contents. Diagnosis of heart disease is a significant and tedious task in medicine. The term Heart disease encompasses the various diseases that affect the heart. There are several classification techniques like Naïve Bayes classification, Support....
Keyword: Classification, Prediction, Accuracy, Diagnosis, Heart

Copy and Paste

Sapna Sharma, Dr. Pankaj Sharma "Classification Algorithms: A Recent Empirical Comparative Survey " Vol. 9 - No. 8 (Aug. 2019), International Journal of Engineering Research and Applications (IJERA) , ISSN: 2248-9622 , www.ijera.com